Table Improvement |
Post Reply | Page <12 |
Author | |
Cactus_Hawk
Newbie Joined: 28 Oct 2018 Location: Phoenix Online Status: Offline Posts: 5 |
Topic: Table Improvement Posted: 29 Oct 2018 at 3:36pm |
No real repair needed as there are only three small holes where the old screws went into the floor. Can’t even see them unless you know exactly where they were...and even then it’s hard to find them.
|
|
offgrid
Senior Member Joined: 23 Jul 2018 Online Status: Offline Posts: 5290 |
Posted: 29 Oct 2018 at 5:29pm |
Great, thanks!
|
|
1994 Chinook Concourse
1995 RV6A Experimental Aircraft 2015 Rpod 179 - sold |
|
StephenH
podders Helping podders - pHp Joined: 29 Nov 2015 Location: Wake Forest, NC Online Status: Offline Posts: 6326 |
Posted: 29 Oct 2018 at 6:47pm |
Very nice indeed! Do you have any sort of spring on the legs to help raise the table and/or keep it upright or does the lid to your new ottoman serve the purpose to keep it upright when it is in place?
|
|
StephenH
Happy is the man that findeth wisdom,... ouR escaPOD mods Former RPod 179 Current Cherokee Grey Wolf 24 JS |
|
Cactus_Hawk
Newbie Joined: 28 Oct 2018 Location: Phoenix Online Status: Offline Posts: 5 |
Posted: 29 Oct 2018 at 8:01pm |
I wanted to add springs but could not find ones that fit right (problem with my design). The good news is the lid to the ottoman holds the legs in place really tight so no real need. The springs would have helped with lifting the table into position but it’s not that heavy. I made this on the fly and if I did it again I would make a few changes. Springs would be one and another type of wood would be another. Popular might have been a better choice to match the existing wood/fake wood. I found the stain color on this forum and it matches well but the grain of the oak not so much. |
|
StephenH
podders Helping podders - pHp Joined: 29 Nov 2015 Location: Wake Forest, NC Online Status: Offline Posts: 6326 |
Posted: 30 Oct 2018 at 12:11am |
One caveat on using Poplar for the top: It warps with changes in humidity! I made a table and will need to re-do the top as the boards warp. The one way I could fix it would be to cut the top into strips and reverse alternate ones, gluing them together with splines or biscuits to keep them from separating. That way, the tendency to warp would be mitigated by grain not all running in the same direction.
|
|
StephenH
Happy is the man that findeth wisdom,... ouR escaPOD mods Former RPod 179 Current Cherokee Grey Wolf 24 JS |
|
GlueGuy
Senior Member Joined: 15 May 2017 Location: N. California Online Status: Offline Posts: 2654 |
Posted: 30 Oct 2018 at 10:09am |
Like the idea very much BTW.
|
|
bp
2017 R-Pod 179 Hood River 2015 Ford F150 SuperCrew 4WD 3.5L Ecoboost |
|
StephenH
podders Helping podders - pHp Joined: 29 Nov 2015 Location: Wake Forest, NC Online Status: Offline Posts: 6326 |
Posted: 30 Oct 2018 at 7:04pm |
Plywood would be the easier way to go and I have been considering using it to replace the warped poplar top. I was thinking of using a thin trim strip around the edges which could be poplar or other wood, possibly contrasting. That way, I would not have the plywood veneer edges to look at. It could also be an angle strip and then it would make a rim around the edges. That would work on the outsides, but not the place where they come together. I would not want a ridge down the middle of the table when it is set up. Right now, I can't do anything about it since the table is in our R-Pod at the dealer's service department. It will probably be at up to five more weeks before we get it back.
|
|
StephenH
Happy is the man that findeth wisdom,... ouR escaPOD mods Former RPod 179 Current Cherokee Grey Wolf 24 JS |
|
Post Reply | Page <12 |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |