Replacing the propane detector sensor |
Post Reply | Page 12> |
Author | |
codycountry
Senior Member Joined: 26 Jan 2014 Location: Wyo Online Status: Offline Posts: 168 |
Topic: Replacing the propane detector sensor Posted: 03 Aug 2018 at 5:41pm |
My propane sensor started beeping without the propane even being turned on, and I discovered that they only last about five years before replacement is required. It's down at floor level in our 2013 model 177 below and left of the bath. It is also the one main thing that runs battery's down over time, since it is powered directly from the DC and does not run off of an internal battery like the carbon monoxide and smoke detector's do. Very simple to replace. I ordered the exact same model off of Amazon for 59 bucks. That is key to get the same exact model. Took off the old one but the wires wouldn't come through the wall due to big factory connectors behind the wall hanging up on the small opening they cut. So I just cut the existing wires very long at the back of the faulty unit, stripped them, took the new unit and twisted with the stripped wires I cut, wrapped both with electrical tape, and slid the new working unit back on to the backing plate. You have to take the backing plate off of the new unit and pitch it if you do it this way, and just use the one already mounted to the wall. It took maybe ten minutes. It is now working perfectly and is good to go for another five years. No trip to the dealer and probably an hour's labor charge, required. Anybody can do this maintenance repair.
|
|
Keith-N-Dar
podders Helping podders - pHp Joined: 03 Apr 2011 Location: Mayville, WI Online Status: Offline Posts: 1447 |
Posted: 03 Aug 2018 at 6:02pm |
If you just twisted and taped the wires you have a high likelyhood of failure. Splices should be soldered, wire nutted or crimped butt splices.
|
|
Keith-N-Dar
Boris & Betty (Boston Terriers) 2011 R-Pod 177 2010 Ford F-150 |
|
codycountry
Senior Member Joined: 26 Jan 2014 Location: Wyo Online Status: Offline Posts: 168 |
Posted: 03 Aug 2018 at 6:15pm |
Actually I used two of those little plastic wing nut things you twist on, then wrapped each of those and the wires with electrical tape. Thinking that five years from now it will be easy to replace again without the solder. Thanks for pointing out my omission.
|
|
TheBum
Senior Member Joined: 26 Feb 2016 Location: Texas Online Status: Offline Posts: 1407 |
Posted: 06 Aug 2018 at 11:27am |
I got tired of always kicking the detector off the wall, so when ours failed, I bought one of the flush mount ones. I had to do some sawing on the paneling, but it's not difficult: I used the saw blade in my Leatherman Juice. For the wiring, I used crimped butt connectors.
|
|
Alan
2022 R-Pod 196 "RaptoRPod" 2022 Ram 1500 Lone Star 4x4 Three cats |
|
Tars Tarkas
Senior Member Joined: 14 Jan 2013 Location: Near Nashville Online Status: Offline Posts: 1447 |
Posted: 06 Aug 2018 at 7:01pm |
Did the same thing. Very happy with the flush model. TT
|
|
2010 176
FJ Cruiser |
|
DavMar
Senior Member Joined: 04 Aug 2017 Location: Lexington, NC Online Status: Offline Posts: 592 |
Posted: 10 Aug 2018 at 5:31pm |
Kind of on subject but on our recent month out on the road I was snoozing in the pod when the wife decided she wanted a glass of wine. In the 180 there is a perfect shelf nook on the left side of the slide out for her to place a box wine carton. Unfortunately the sensor for the Propane/CO2 is located just under it a bit forward near the floor. Well she pours her wine but somehow spilled some on the floor and the next thing I know I'm being rocked awake by the beep, beep, of this alarm. Seems we found out the hard way the fumes of alcohol will set off this alarm! Another thing on this trip we found out will set off this alarm is if your converter dies and the voltage drops to below 6 volts, crazy! I need to figure out what fuse controls this alarm so if I ever need to kill it again I can.
|
|
Dave & Marlene J with Zoey the
wonder dog. 2017 Rpod 180 2016 Toyota Tacoma SR5 4x4 Lexington, NC |
|
StephenH
podders Helping podders - pHp Joined: 29 Nov 2015 Location: Wake Forest, NC Online Status: Offline Posts: 6326 |
Posted: 10 Aug 2018 at 10:26pm |
Unfortunately, it is hard-wired and does not go through the fuse panel. It has to be to prevent someone from disabling it which would defeat the purpose of having it which is to keep someone from dying from CO poisoning or from going up with a bang if there is a propane leak.
|
|
StephenH
Happy is the man that findeth wisdom,... ouR escaPOD mods Former RPod 179 Current Cherokee Grey Wolf 24 JS |
|
DavMar
Senior Member Joined: 04 Aug 2017 Location: Lexington, NC Online Status: Offline Posts: 592 |
Posted: 11 Aug 2018 at 3:33pm |
That explains why I couldn't find the fuse! I may just wire in line a SPST toggle switch with it and stuff it back into the wall with the wiring. At least that way you could disable the alarm when you determined there is no Propane or CO2 leak.
|
|
Dave & Marlene J with Zoey the
wonder dog. 2017 Rpod 180 2016 Toyota Tacoma SR5 4x4 Lexington, NC |
|
Tars Tarkas
Senior Member Joined: 14 Jan 2013 Location: Near Nashville Online Status: Offline Posts: 1447 |
Posted: 11 Aug 2018 at 5:20pm |
I know it's just sort of a typo, but it's a CO detector. CO2, carbon dioxide, could suffocate you under almost impossible circumstances. CO, carbon monoxide, is a deadly poison that can kill you in your sleep very easily. In my opinion, overriding the always-on feature of these detectors is a very serious safety concern. It's best to resolve whatever sets it off by opening the doors, cranking up the vent fan, or charging the battery than disabling it and risk forgetting to turn it back on. You could wake up dead. Also, as someone else noted, these detectors have expiration dates. They have to be replaced about every 5 years. TT
|
|
2010 176
FJ Cruiser |
|
mcarter
podders Helping podders - pHp Joined: 07 Apr 2016 Location: Greenbrier, TN Online Status: Offline Posts: 3419 |
Posted: 11 Aug 2018 at 5:22pm |
+1 - Mistake to bypass this safety device.
|
|
Mike Carter
2015 178 " I had the right to remain silent, I just didn't have the ability." |
|
Post Reply | Page 12> |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |