Author |
Share Topic Topic Search Topic Options
|
GlueGuy
Senior Member
Joined: 15 May 2017
Location: N. California
Online Status: Offline
Posts: 2629
|
Topic: I was Sold the wrong WDH...What effects??? Posted: 09 Feb 2019 at 1:17pm |
Right. Except that both trucks say "Ford F-150" in their names, there are numerous differences. Ours is an HRE RP-179 (higher stance) with 15" tires (another 1/2"higher).
Our F-150 is the 2015 "all aluminum" one, plus 4WD, plus the extended 157" wheelbase; all of which make it taller.
None-the-less, the basic rules for setting up the WDH still hold.
|
bp
2017 R-Pod 179 Hood River
2015 Ford F150 SuperCrew 4WD 3.5L Ecoboost
|
![Back to Top Back to Top](forum_images/back_to_top.png) |
TearlessTom
Groupie
Joined: 25 Jan 2019
Location: Spanish Fort AL
Online Status: Offline
Posts: 85
|
Posted: 24 Mar 2019 at 12:00pm |
Okay guys I've done a lot more reading and research and crawling under the Pod etc.
I have found that they changed the axle "clocking" a year or two prior to my 2017 being made. To verify my axle is "clocked" at about the 4:00 - 4:30 position so it is already raised a bit vs prior years that as I understand it the risers were made for.
So from what I've read Risers are not needed for my Pod because of the axle clocking.
Is this correct?
Also, I still want to change to the 15 inch tire for peace of mind with an increased load rating and speed rating. Not planning on over loading or speeding but I do like the idea of the added safety margin that they give.
I know I need to measure the wheel well clearance but haven't thought of it when I had a tape measure in my hand.
Most suggest the 205/75/15 is the 225/75/15 too much of a increase in height and width over the 205/75/14 which I have on now?????
205/75/14 = 26.1 height 8.1 width
205/75/15 = 27.1 height 8.1 width
225/75/15 = 28.3 height 8.9 width.
|
Tearless Tom
2017 R-Pod 180
2014 Ford F-150 XLT 2WD 5.0
|
![Back to Top Back to Top](forum_images/back_to_top.png) |
GlueGuy
Senior Member
Joined: 15 May 2017
Location: N. California
Online Status: Offline
Posts: 2629
|
Posted: 24 Mar 2019 at 1:31pm |
Originally posted by TearlessTom
Okay guys I've done a lot more reading and research and crawling under the Pod etc.
I have found that they changed the axle "clocking" a year or two prior to my 2017 being made. To verify my axle is "clocked" at about the 4:00 - 4:30 position so it is already raised a bit vs prior years that as I understand it the risers were made for.
So from what I've read Risers are not needed for my Pod because of the axle clocking.
Is this correct?
|
I think that's correct. Our 2017 HRE does not have the risers.
Originally posted by TearlessTom
Also, I still want to change to the 15 inch tire for peace of mind with an increased load rating and speed rating. Not planning on over loading or speeding but I do like the idea of the added safety margin that they give.
I know I need to measure the wheel well clearance but haven't thought of it when I had a tape measure in my hand.
Most suggest the 205/75/15 is the 225/75/15 too much of a increase in height and width over the 205/75/14 which I have on now?????
205/75/14 = 26.1 height 8.1 width
205/75/15 = 27.1 height 8.1 width
225/75/15 = 28.3 height 8.9 width. |
The difference in radius of the 205/75/14 and the 205/75/15 is a half inch. I would measure the amount of space you have between the smaller tire and decide if you could tolerate a half inch less of it.
|
bp
2017 R-Pod 179 Hood River
2015 Ford F150 SuperCrew 4WD 3.5L Ecoboost
|
![Back to Top Back to Top](forum_images/back_to_top.png) |
offgrid
Senior Member
Joined: 23 Jul 2018
Online Status: Offline
Posts: 5290
|
Posted: 24 Mar 2019 at 1:56pm |
I'm under the impression that the torsion axle start angle change (aka clocking) doesn't quite give you the same height as the riser kit, but I might be wrong.
My suggestion is to measure as GlueGuy says and then get the LRD one with the highest load rating that you have clearance for Since you're getting new wheels too be sure to check the load rating on those, you're only as good as your weakest link. I got these, both tires and wheels rated for 2540 lbs. It also saves the mounting cost.
|
1994 Chinook Concourse
1995 RV6A Experimental Aircraft
2015 Rpod 179 - sold
|
![Back to Top Back to Top](forum_images/back_to_top.png) |
TearlessTom
Groupie
Joined: 25 Jan 2019
Location: Spanish Fort AL
Online Status: Offline
Posts: 85
|
Posted: 25 Mar 2019 at 8:03am |
Originally posted by offgrid
I'm under the impression that the torsion axle start angle change (aka clocking) doesn't quite give you the same height as the riser kit, but I might be wrong. My suggestion is to measure as GlueGuy says and then get the LRD one with the highest load rating that you have clearance for Since you're getting new wheels too be sure to check the load rating on those, you're only as good as your weakest link. I got these, both tires and wheels rated for 2540 lbs. It also saves the mounting cost.
|
Are you having any wheel well clearance issues with that tire? That was my biggest concern .
Do you have risers on yours or not. That is the set up I was wanting to order.
Oh by the way I attempted to measure my wheel well clearance last night with a steel tape I had handy. Clearance with the 205/75x14 was approx. 3.25 - 3.5 inches.
|
Tearless Tom
2017 R-Pod 180
2014 Ford F-150 XLT 2WD 5.0
|
![Back to Top Back to Top](forum_images/back_to_top.png) |
offgrid
Senior Member
Joined: 23 Jul 2018
Online Status: Offline
Posts: 5290
|
Posted: 25 Mar 2019 at 8:58am |
No wheel clearance issues, and yes I have the risers. FWIW, the trailer also looks much better balanced with the bigger wheels on it.
|
1994 Chinook Concourse
1995 RV6A Experimental Aircraft
2015 Rpod 179 - sold
|
![Back to Top Back to Top](forum_images/back_to_top.png) |