R-pod Owners Forum Homepage

This site is free to use.
Donations benefit a non-profit Girls Softball organization

Forum Home Forum Home > R-pod Discussion Forums > Podmods, Maintenance, Tips and Tricks
  New Posts New Posts RSS Feed: Anode Rod
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Topic ClosedAnode Rod
 Post Reply Post Reply Page  12>
Author
Message Reverse Sort Order
  Share Topic Share Topic  Topic Search Topic Search  Topic Options Topic Options
hogone View Drop Down
Senior Member
Senior Member
Avatar

Joined: 09 Apr 2013
Location: St. Louis
Online Status: Offline
Posts: 1043 		Direct Link To This Post Topic: Anode Rod
    Posted: 11 May 2013 at 6:48pm
rog on all that
Back to Top
TIDALWAVE View Drop Down
Senior Member
Senior Member
Avatar

Joined: 21 Nov 2009
Location: MINNESOTA
Online Status: Offline
Posts: 315 		Direct Link To This Post Posted: 11 May 2013 at 6:30pm
TongueSome of the anode rod will dissolve in the water. However, the loss of anode metal is not usually symmetrical so rod material will may break off into the heater from road vibration, etc.
I have found that it is a good idea to flush out the water lines by removing the aerators from the faucet outlets, and flushing some water through the lines at the beginning and end of each season.
I also wash out the aerators, if I notice some whitish sediment in/on the aerators.
The amount of rod loss depends on the chemistry of the water used.  I have had rods last multiple years and then barely last one season.  A rod that is nearly dissolved away is demonstrating the protection it has given to your heater.  Replacing a $15 rod is certainly cheaper than replacing a water heater tank.
Over the last couple of seasons, I have been draining the heater tank, if I do not expect to use the Pod for an extended period of time.  The longer the time water sits in the tank, the more loss of rod material.  I make sure that I fill the tank before I leave for the next trip...I don't want the tank to burn out because it was empty when I turn on the gas or the 110 house current
TIDALWAVE
Back to Top
gappman View Drop Down
Newbie
Newbie
Avatar

Joined: 12 Mar 2013
Location: United States
Online Status: Offline
Posts: 13 		Direct Link To This Post Posted: 11 May 2013 at 3:14pm
I did this at the recommendation of my parents who have been RV'ing most of their lives. No issues with water heaters for them and I drain the thing thoroughly when I return home. My trips are hardly longer than 3 days at a time anyway. 
Gary Piazza
www.garypiazza.com
Back to Top
Tars Tarkas View Drop Down
Senior Member
Senior Member
Avatar

Joined: 14 Jan 2013
Location: Near Nashville
Online Status: Offline
Posts: 1446 		Direct Link To This Post Posted: 11 May 2013 at 11:31am
Originally posted by gappman

I pulled mine out and put a drain petcock in its place. 


  Not a good idea!  Google anode rod a little bit and find out why water heater manufacturers put these annoying little consumables in their water heaters in the first place.  They aren't necessary in the short run but they have a major impact on the life of your water heater.  Considering that most, if not all, of the opportunity for water heater failure is while you're on the road away from home, the inconvenience of fixing or replacing a water heater probably outweighs the expense, which will be way more than the cost of an anode rod.

  TT
Back to Top
hogone View Drop Down
Senior Member
Senior Member
Avatar

Joined: 09 Apr 2013
Location: St. Louis
Online Status: Offline
Posts: 1043 		Direct Link To This Post Posted: 11 May 2013 at 7:39am
mine is half gone as well...........do you know if it basically dissolves, or are there actually chunks of it inside the heater?
Back to Top
Keith-N-Dar View Drop Down
podders Helping podders - pHp
podders Helping podders - pHp
Avatar

Joined: 03 Apr 2011
Location: Mayville, WI
Online Status: Offline
Posts: 1447 		Direct Link To This Post Posted: 11 May 2013 at 7:07am
In two seasons mine is half gone.  I would rather have the sacrificial rod melting instead of the heater.  
Keith-N-Dar
Boris & Betty (Boston Terriers)
2011 R-Pod 177
2010 Ford F-150
Back to Top
gappman View Drop Down
Newbie
Newbie
Avatar

Joined: 12 Mar 2013
Location: United States
Online Status: Offline
Posts: 13 		Direct Link To This Post Posted: 11 May 2013 at 1:01am
I pulled mine out and put a drain petcock in its place. 
Gary Piazza
www.garypiazza.com
Back to Top
Tars Tarkas View Drop Down
Senior Member
Senior Member
Avatar

Joined: 14 Jan 2013
Location: Near Nashville
Online Status: Offline
Posts: 1446 		Direct Link To This Post Posted: 06 May 2013 at 9:06pm
Pipe threads are meant to get tight.
TT
Back to Top
Outbound View Drop Down
podders Helping podders - pHp
podders Helping podders - pHp
Avatar

Joined: 19 Nov 2009
Location: Oshawa, Ontario
Online Status: Offline
Posts: 767 		Direct Link To This Post Posted: 06 May 2013 at 6:42pm
Use a brass brush to clean the threads - I bought a toothbrush-shaped one at the dollar store that works great.

Also, my plug doesn't screw flush into the heater; it sits proud about 3/8".  That said, YMMV
Craig :: 2009 RP171 towed by a 2017 F150
Back to Top
Keith-N-Dar View Drop Down
podders Helping podders - pHp
podders Helping podders - pHp
Avatar

Joined: 03 Apr 2011
Location: Mayville, WI
Online Status: Offline
Posts: 1447 		Direct Link To This Post Posted: 05 May 2013 at 8:27pm
The plug is pipe thread.  Pipe thread is tapered so it will run tight and not leak.  As said, add tefflon tape, make tight, check for leaks, camp.
Keith-N-Dar
Boris & Betty (Boston Terriers)
2011 R-Pod 177
2010 Ford F-150
Back to Top
 Post Reply Post Reply Page  12>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.64
Copyright ©2001-2009 Web Wiz