erratic brake light connection - Event Date: 17 Nov 2014 |
Post Reply | Page 12> |
Author | |
Happy Tripping
Senior Member Joined: 27 May 2014 Online Status: Offline Posts: 473 |
Calendar Event: erratic brake light connection Posted: 17 Nov 2014 at 12:54pm |
7 month old r-pod, used on several multi-hundred mile trips with no problems.
I recently checked my brake lights on setting out and they didn't work, turn signals and emergency blinkers were ok. I wiggled the 7 pin connection and they worked, I didn't recognize any problems on the subsequent 6 hour trip. I don't believe it's a loose wire, it seemed to be a poor electric 'connection'. Is this 'on again - off again' condition common? Can I prevent this with some sort of 'lubricant'? One forum member likes 'dilectric grease', but this seems to be messy and for rubber connections, not inside the metal-to-metal of the socket itself. I am electrically challenged so please keep it simple. Thanks for any info. |
|
Podster
Senior Member Joined: 16 Sep 2014 Location: San Antonio Online Status: Offline Posts: 1108 |
Posted: 17 Nov 2014 at 1:21pm |
On my connector the spring loaded cover over the receptacle actually acts as a plug keeper as well. It may be that you are not getting the plug inline and/or the lid in the right position to benefit from the latch (keeper) to keep the receptacle from moving around.
There is more to the connector than just opening and connecting and pushing the plug in, at least on mine anyway. Take a look at the spring loaded lid with the plug in place and see if you can find a spot where the lid supports the plug and keeps it from backing out or shifting. Good Luck! |
|
Cliff & Raelynn
Ranger 4.0/178 (1/2 ton 5,800lb tow capacity) |
|
hogone
Senior Member Joined: 09 Apr 2013 Location: St. Louis Online Status: Offline Posts: 1043 |
Posted: 17 Nov 2014 at 1:59pm |
i have noticed that on mine on a couple occessions, my brake controller light will go out. i get mine pushed in all the way, have the spring laoded cover lid on properly; i guess it just wiggles slightly loose. i now keep a very close eye on it as i do not want to lose my trailer brakes. hogone
|
|
Jon & Pam
2013 RP177 2010 F150 2017 HD Streetglide 2009 HD Lowrider CHEESEHEAD |
|
Luv2Q
Senior Member Joined: 30 Aug 2014 Location: Central TX Online Status: Offline Posts: 309 |
Posted: 17 Nov 2014 at 2:06pm |
I noticed a similar problem when we brought our Pod home from Ohio. Turned out to be a sloppy fit where the 7-pin male (trailer) end connected to the female (truck) end. The spring-loaded keeper was doing its job & keeping the plug from falling out but it was still making a poor connection. My jury-rigged solution: a heavy rubber band to force the connection to be snug. (And yes, I need to find a better long-term solution )
|
|
John & Teri
Tundra 5.7L V8 / RP 180 E2 WDH / Integrated controller (POS) replaced by Tekonsha P3 |
|
techntrek
Admin Group - pHp Joined: 29 Jul 2009 Location: MD Online Status: Offline Posts: 9059 |
Posted: 17 Nov 2014 at 2:09pm |
Worst case you may have to bend the pin in the Bargeman so it makes better contact.
|
|
Doug ~ '10 171 (2009-2015) ~ 2008 Salem ~ Pod instruction manual
|
|
john in idaho
Senior Member Joined: 04 Nov 2014 Location: Eagle Idaho Online Status: Offline Posts: 611 |
Posted: 17 Nov 2014 at 5:12pm |
You could try spraying the plug and receiver with electronic parts cleaner from NAPA. May require a Q tip at the same time. It dries very quickly… as in 10-15 seconds. I use it in my antique vehicles when the key switch acts funny, or the starter solenoid sticks.
|
|
Outbound
podders Helping podders - pHp Joined: 19 Nov 2009 Location: Oshawa, Ontario Online Status: Offline Posts: 767 |
Posted: 17 Nov 2014 at 5:19pm |
Count me as a second forum member who likes dielectric grease. Its really not very messy at all. And, as someone who's had similar connectivity issues, it works very well. Before you do anything tho, use some emery paper to sand down the terminals on the r-pod's Bargman connector. Folding a very narrow piece over the end of a flat screwdriver works well. Then, use a Q-Tip to apply dielectric grease onto the Bargman connector's terminals - push it down in there. With a paper towel, wipe off any excess that you may get on the rubber.
|
|
Craig :: 2009 RP171 towed by a 2017 F150
|
|
Outbound
podders Helping podders - pHp Joined: 19 Nov 2009 Location: Oshawa, Ontario Online Status: Offline Posts: 767 |
Posted: 17 Nov 2014 at 5:28pm |
One thing concerns me tho: brake lights on setting out and they didn't work, turn signals and emergency blinkers were ok. The brake lights, the turn signals and the emergency blinkers all run through the same two wires (three, if you count the ground to complete the circut) - the 5 and 6 pins. If your problem is at the connector, then they'd either all work or none work. |
|
Craig :: 2009 RP171 towed by a 2017 F150
|
|
techntrek
Admin Group - pHp Joined: 29 Jul 2009 Location: MD Online Status: Offline Posts: 9059 |
Posted: 17 Nov 2014 at 6:12pm |
Good catch Craig, that might mean the problem is related to the trailer light converter.
|
|
Doug ~ '10 171 (2009-2015) ~ 2008 Salem ~ Pod instruction manual
|
|
Podster
Senior Member Joined: 16 Sep 2014 Location: San Antonio Online Status: Offline Posts: 1108 |
Posted: 17 Nov 2014 at 8:13pm |
I have seen electrical connections with multiple loads work, but then fail when the greater load (like the break lights) was applied.
|
|
Cliff & Raelynn
Ranger 4.0/178 (1/2 ton 5,800lb tow capacity) |
|
Post Reply | Page 12> |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |